Ground Control to Major TOM
I’m still editing together the epic electronics replacement and soldering series of videos. Nearly done! Meanwhile, here’s a really short video on how to diagnose and fix ground connection problems in your guitar.
I’m still editing together the epic electronics replacement and soldering series of videos. Nearly done! Meanwhile, here’s a really short video on how to diagnose and fix ground connection problems in your guitar.
December 9, 2009 @ 12:01 pm
This is a cool site and very helpful to a lot of guitarists also. I have a question if i may ask it. I just bought a new ibanez gax70 and after i finish playing distortion i hear a aggravating hum and the only way i can stop it is to touch the jack then it is normal. Has anybody else ever had this problem before? Thanks and have a great day everybody.
December 9, 2009 @ 2:34 pm
That’s a nice looking guitar. But an odd problem! 🙂
Need to ask some questions about your symptoms – you say it starts humming after playing distortion (no hum before you play?) and then it goes away when you touch the jack (how about then after you let go of the jack again?)
– You only hear the hum when playing distorted? How about on a clean channel, turned up really loud? (Distortion may be gaining up a hum that is always there)
– What is doing the distortion? Is is perhaps a multi-effects unit or amp with a noise gate or noise suppressor in it?
-John
December 9, 2009 @ 2:56 pm
well i don’t have a effects pedal at this time so i just play through the half stack. when it is on clean you hear nothing but when you hit distortion and stop playing and leave it on distortion you hear the hum. i have another gsx70 also and i hokked that one up and you dont hear the hum at all on that one.
December 9, 2009 @ 3:07 pm
Could it be that the extra gain on your amp’s distorted channel is causing your pickups to go microphonic…? I guess not – since I’d describe that sound as more of a squeal than a hum.
– Can you describe the hum? (Or better yet, make a recording of it?)
– Does the sound change as you move around?
Also my other two questions:
– there’s no hum before you start playing, but after you stop playing, you hear it?
– it goes away when you touch the jack, but what happens then when you stop touching the jack?
– you said your other guitar is a gsx70- did you mean another gax70 – the identical guitar with the same pickups? if so, that would probably rule out things like pickups, etc.
hmm
December 9, 2009 @ 3:19 pm
yes my other guitar is also a gax70. when i stop touching the jack the hum comes back. and the new gax70 i just got has a little different style pickups. i know this sounds weird without hearing it but i have no way of recording it at this time. i have a boss noise supressor buti was hoping to fix it without having to use it being that my older gax70 does’nt make any noise at all.
December 9, 2009 @ 3:23 pm
well my older gax has different pickups but being that when i touch the jack on the new gutiar it looks like to me it has something to do with the jack or maybe a loose ground perhaps…
December 9, 2009 @ 3:39 pm
i have a behringer v-tone head.
December 9, 2009 @ 3:47 pm
I’m thinking you have a loose ground wire. Your v-tone head may be tweaking the hum if its expander is engaged. Double-check that all effects are bypassed on the head. An expander with a fast attack and slow delay could be reducing the hum before you play, and revealing the hum afterwards.
If you have a multi-meter, double check that you have a good connection between all metal parts on the guitar and the jack shield.
-John
December 9, 2009 @ 4:52 pm
well the weird thing is it only hums with the new guitar not the old one and i had a guitar shop check all the wiring in it and he said nothing was wrong with it….this guitar sucks big time..i know anything can be fixed but i’m not so sure about this one..it makes me wont to stop playing all around and find a new hobby…
December 9, 2009 @ 9:29 pm
i found the problem…somehow a ground was tied in to where i could’nt see it until i moved a few wires around so now all i need to do is make sure i clean the surface good and solder it good. i figured it was something simple…anyway thanks for all the advice on this problem and i’ll follow up tommorrow once i get the wire in place…
December 9, 2009 @ 9:48 pm
Great! Glad to hear it.
February 9, 2010 @ 4:31 pm
Hi John, thank for your very instructive video on guitar wiring, potentiometer test and other. I’m actually confuse because I have all the noise problem that you show in your video + increase noise because of halogen lamp in my practice room (playing in the dark actually help to decrease this noise!). On the other hand, when I look for connectivity between various part (not to say all) I have a perfectly grounded guitar. The multimeter put on the strings key’s and on the metal part of the output jack is good. I don’t know what to think! Maybe desolder everything, start over and add some shielding in the cavity of my GODIN guitar (nice guitar from Quebec). Any suggestion? Oh I forgot. The problem is new and came after replacing my volume knob.
February 9, 2010 @ 4:56 pm
Hi Charles,
I was about to say “Yes, it must be a shielding problem”, until you said that this is a NEW problem with your new volume knob, and didn’t happen before that.
In that case, there MUST be a problem with the wiring of the new volume pot. Are you sure you wired it up identically to before? Same exact wire topology, same wire, etc? Is it possible that you wired up the new volume pot ground differently from before and introduced a ground loop?
-John
February 10, 2010 @ 4:19 pm
Hi John, fast answer! Thank you. I rewired the pot exactly has before (really) double,triple check even more! So, today I decided to shield every possible part of my guitar while testing with the multimeter the connectivity. At the same time, I had to desolder-resolder everything for the shielding and I therefore check connectivity after each resoldering step. Ouf! lots of work. Result: I’d say about 10% noise reduction (my shielding can’t be done under the pickup without being apparent so I can’t do this part).
The noise become more important when I crank the amp volume up a notch or two and when my room halogen lamp is on. Again, when I touch the metal part on my guitar the buzz increase or decrease depending on where I touch it. I really feel that it’s a pickup problem but I don’t really know.
About the ground loop hypothesis. I think I’m ok. My volume pot work has a Hub for ground. The ground come from 1) the tone, 2) the switch (I have grounded the metal part of the switch even do It was not made to be ground at first) 3) the tremolo bar, 4) the new ”home made” shield is connected true the switch which then go to the volume pot. 5) three pickup grounded twice again on the volume pot: one for the ”pickup shield” and one for the ”pickup ground”. My pickup are humbucker (four wire + shield ground). The bridge is a hotrails from seymour duncan and the neck and middle are ”godin” alias Schaller pickup.
All these ground unified on the pot knob are redirected out to the output jack. I did make sure (with a multimeter) not to inverse the connection there to! I even verify If my home wiring (were I connect the amp) was grounded and it is.
Does Overheating a pot can do that?
My hotrails pickup don’t SEEM to be waxed or potted they say? 100$ from this compagny I doubt they haven’t think about that!
I’m out of idea!
-Charles
PS, sorry for my english, I speak french
May 18, 2010 @ 5:24 pm
I have a Yamaha Acoustic Electric – long story short- I’ve been working on it and I don’t usually plug into an amp much- but since I had been working on the saddle – i wanted to make sure the pick up is still working… so I plugged it in to my sister’s crate amp – and when I turned up the volume on the guitar (pre-amp) and then the volume on the crate amp- I could hear the guitar strings – (they work) but there is this horrible buzz which was only relieved when I put my hand around the cord on my guitar’s output jack… Any suggestions? I appreciate any help. Thanks
May 25, 2010 @ 3:10 pm
Since you have an active preamp in there, it could be a number of things. Did you try a fresh battery? It could also be a missing or broken ground wire somewhere, as I demonstrate in the video.
June 3, 2010 @ 2:37 pm
Hey I have a question….I have been soldering my guitars for 8 years and never had this before….I broke my volume knob and replaced it the other day…Ever since my guitar has had a horrible hum that is very present in the dist. channel…on top of that it has made my amp very noisey sounding too when I have it plugged in…always some degree of noise but mainly when the volume pot is up all the way. Bad Hum. I tryed resoldering it like 6 times and the last time I redid the whole guitar. Not sure what the problem could be but I really need help with this one…could it be that because my soldering Iron tip is so old and dis-colored that it caused a cold solder joint? Also I noticed the solder isn’t really shinny…it’s kinda dull. I am hoping a new tip on the iron will fix this right up…haha…please help
~Thanks
June 3, 2010 @ 2:44 pm
Oh i should probly also mention that I have an Ibanez 7620 with a Dimarzio D-sonic 7, with a Dimarzio EP1111 3 way switch in the guitar… No problems out of that at all…it’s wired like a JP7 Musicman. There was a cap on the old volume knob..but I assumed it was for treble responsiveness with changeing the volume amount on the instrument..Like a .22 or something. The Hum also does NOT change by letting go of the strings or touching them….so I’m more baffled…which is why I was thinking cold solder joint
June 3, 2010 @ 5:25 pm
I don’t think a cold solder joint will cause hum like this- it’ll just make the connection more likely to break.
Assuming everything else was working fine, and it started sounding bad when you replaced the pot – I’d think you either made a wiring mistake, or the pot is wrong/bad somehow. Do you have another pot you can swap in to try?
Does the new volume pot work at all for volume control? The cap on the old volume pot was probably for treble bleed and can be left off.
Like I mention in my FAQ, using alligator clips to test and isolate issues like this (before soldering) can be a big help. I know you’ve already resoldered the whole thing, but you may need to start taking it apart again to isolate the problem…
Hope this helps.
John
June 3, 2010 @ 8:43 pm
Hey John…yes, I will be tomorrow attempting a new pot. I did wire it exactly the same as it was before…Tryed putting the broke jack back in just to see if it made the noise and of coarse it did. haha. But everything funtions completely normal…volume works great and everything…just the noise…I am gonna also attempt a new soldering iron tip tomorrow with the new pot. Thanks for the reply and I’ll let you know what the deal is if it fixes it.
June 23, 2010 @ 2:20 pm
Hi John,
After months of waiting for parts I have finally upgraded pots,cap, Jack etc in pretty much the exact way as yourself on my Riviera. I have got to the end and I have some kind of very slight ground fault. I have also changed the neck pick up for a Heywood Pickups 8.5k to hopefully give it a bit of a clearer sound at the neck. I think I should point out is the new pickup has a ground for the pickup cover which I have no idea what to do with??
I have tried it in different locations and the fault is still there.I have resoldered twice and performed continuity tests and all seems OK? I’m baffled…… Any suggestions??
Great site by the way 🙂
Kiddakidda
June 23, 2010 @ 4:12 pm
Grounding the pickup cover at the same place as the other pickup ground should be ok.
It’s conceivable you have a ground loop– where there’s more than one path to ground. If you think of the jack ground as the “destination”, check each ground source (like your pickup ground) and make sure that there’s only one path for it to reach the jack ground destination. See here for some pictorials of this idea:
http://alexplorer.net/guitar/basics/grounding.html
Again, I recommend using alligator leads while you’re experimenting to make sure you get it all right, before soldering.
Hope this helps,
John
June 24, 2010 @ 1:29 pm
Cheers John,
In an attempt to try and isolate the problem I have took certain elements ‘out of the chain’ so to speak. I have now got to the stage where I have one pickup attached to the jack ONLY!! with the bridge ground wire and I still have a slight hum. When I touch any part of the bridge I can hear the amp make a slight click sound and it cuts the noise out. I don’t know what else I can do. The hum is very slight but every time I touch the bridge the noise disapears. I have continuity between the bridge and the bridge wire. What else could this be???
Cheers
Kiddakidda
June 24, 2010 @ 1:49 pm
Great job narrowing it down to just pickup and jack. It does sound like a ground issue.
Single-coils pick up hum, but that doesn’t sound like what you’re hearing since single-coil noise generally does not change when touching the metal of the guitar (though it does change when moving the guitar around).
I assume you’ve also checked for continuity between the bridge, the pickup ground and the jack ground lug?
Other things to try for more data points: use another pickup to rule out an internal defect in the pickup; a different cable to the amp; a different amp.
-John
June 26, 2010 @ 2:13 am
Hi Again John,
I’m at a loss here, my guitar has been stripped down to it’s component parts. I am currently using one pickup directly connected to the jack and I still get the click sound when I touch any metal. I have swapped cables, tried different jacks and tried all four pickups I currently have – no change. I have sanded back the bridge post to get to the raw metal to make sure I haven’t got a poor ground. I have not got another Amp but I have tried my Tele and SG custom in the same amp and they sound sweet and no sounds when touching metal parts. I have even tried another power lead for the Amp just in case. Is it possible that with all the parts out that the guitar is picking up some kind of electrical interference that is affecting the ground???
This has to be something simple, can you make any other suggestions? I feel like throwing the thing in the Bin at the moment!!!
Cheers
Kiddakidda
June 26, 2010 @ 10:12 am
Sounds like you’ve tried everything I would try… If you’ve got it simplified down to just one pickup, the jack, and the ground wire from the bridge, and you hear the same thing with both the Epi pickup and the Heywood pickup, then WTF?!
Are you using long runs of unshielded wire or alligator leads? (These tend to pick up more noise than shielded wire).
-John
June 26, 2010 @ 1:50 pm
Hi John,
This afternoon I moved my Vox AD100VT from the bedroom, downstairs to the kitchen in case it was picking up some unwanted interference somewhere. It was exactly the same downstairs. I then took the jack off and used the aligator leads directly onto the jack plug. Hey Presto!! No noise. I then introduced the jack and it seemed to work fine. I then tried the other pickups and all seemed OK. I then tried my cardboard set of pots, jack and selector and all seemed OK except for the selector in the neck/middle position with the middle volume turned down is creating noise again.
I really think the pickup cover ground is causing me some kind of issue, I also think the poor quality aligator leads I am using may have possibly caused previous problems. I don’t know why I am suddenly not getting the grounding issue apart from what I have mentioned above, which worries me that it may come back at any stage. I’ll keep you posted once I have managed to sort the neck pickup ground problem.
Cheers
kiddakidda
June 25, 2010 @ 8:51 pm
I have a P93 just like yours. The problem i have is while im playing if my finger touches the pickup(even just the black base) I get a loud buzz. You know what could be causing this?
June 26, 2010 @ 10:24 am
I don’t remember whether the metal covers were grounded on those pickups. If you touch a wire or alligator lead between the metal cover and the bridge (or to the jack nut), does it still buzz when you touch with your finger?
If you have a multimeter, check continuity between the metal parts as I describe in the video…
-John
June 26, 2010 @ 1:56 pm
This is really strange, as you will see I have the same issue. The pickup covers are not grounded as far as I can see. I am certainly considering this on my new Heywood pickup to see if it sorts the issue. I’m out of wire now so I’ll need to try and source some tomorrow.
Kiddakidda
June 26, 2010 @ 2:42 pm
Yes I checked everything is grounded except the pickup covers. touching something grounded (ie the jack or bridge) lowers the volume of the buzz but touching the pick up still adds it. At first I thought it might be touching the pickups caused a ground loop but since they arn’t even grounded it cant be that i believe.
June 26, 2010 @ 3:04 pm
Is your guitar stock, or have you done some of John’s mods?
June 26, 2010 @ 3:56 pm
Its stock.
July 8, 2010 @ 1:25 pm
Hi John,
I checked and re-checked my wiring for my Riviera a 100 times now. My new wiring is identical in every way to the original wiring setup. I don’t seem to get the same slight hum and ‘click’ when I touch metal parts when using the guitar downstairs but I seem to get it all the time upstairs when I use my guitar and amp. (I’m whacked from lumping that Vox AD100VT up and down the stairs, it weighs a ton!!) I can only think that I have a possible weak ground/earth on my upstairs house electrics which is causing the ground fault….. What do you think??
Cheers
Kiddakidda
July 8, 2010 @ 5:21 pm
I think you’ve officially entered voodoo black-magic grounding territory 🙂 Sorry I don’t know what else to do.
Play downstairs! 🙂
-John
July 17, 2010 @ 8:36 am
Hey John,
I think I have resolved my slight ground issue. I decided to go down the route of sheilding all 3 pickup cavities and running a ground wire through all 3. I also made a slight lip so the sheilding also touched the pickup covers. Seems to work great and I have no noise!!
I have however another issue that I want to run by you. After finally putting it all back together I have now realised I have a strange volume control issue that wasn’t there when i tested before install. When I turn the Volume control for Middle and Bridge upto ’10’ I get a very big volume drop? If I turn both down slightlt to say ‘9’ the volume returns.
The tone seems to work fine so I am not sure it’s a Tone cap issue. Any ideas?
Cheers John.
Kiddakidda
July 17, 2010 @ 9:01 pm
Excellent work on the shielding! Did you take any pictures?
As for the volume drop, I guess there’s some bad interaction with the way you’ve wired it up. Double/triple check the wiring using your multimeter to check that nothing’s connected that shouldn’t be and the everything that should be connected is 🙂 You could also try writing out the circuit as you’ve wired it (either as an electrical circuit diagram, or as a pictorial of your pickups, pots, caps and wires). In the process of doing that, you might just figure out the problem. But if not, scan it and email to me and hopefully I can help.
-John
July 18, 2010 @ 12:56 am
Cheers John,
I did take some pictures and I will forward to you if you want them? I’m a bit of a novice when using a Multimeter and my knowledge ends when it gets to testing for continuety! Are there any other checks I can do? I’m sure I have copied wire for wire the wiring as it came out originally but I shall try and email you my diagram later today.
Kiddakidda
August 25, 2010 @ 2:12 am
Hey i think that i have the same problem my guitar is an epiphone special 2 (those cheap one) and my amp is an Fender Frontman 25R, and i bought that amp because i thinked that tha amp that i had was tha problem bue it was not.
So my guitar as that problem can you explain me step by step what should i do?
Soorry my english but im portuguese ;D
Il be waiting ;D Cheers
August 26, 2010 @ 9:50 am
Hi Richard,
Use a multimeter to check for a good electrical connection between all the metal parts of the guitar and electronics. Make sure you have a connection all the way from strings to the jack ground lug. Re-solder any broken wires or loose connections as necessary.
For tips on using a multimeter, see my FAQ.
Good luck!
John
December 13, 2011 @ 10:17 am
December 13, 2011 @ 3:28 pm
December 13, 2011 @ 3:31 pm
December 13, 2011 @ 11:59 pm
January 20, 2012 @ 6:55 am
December 28, 2011 @ 4:16 am
January 1, 2012 @ 8:57 pm
January 6, 2012 @ 12:10 am
December 30, 2011 @ 5:32 pm
January 1, 2012 @ 8:58 pm
January 4, 2012 @ 7:47 am
just bought a new decentish cable to try and sounds worse than before. must be the guitar. thanks man. i’ll be messing with the guitars ground soon so i’ll move it to the bridge if i can get the drill to get in there. going to make a faraday cage in there too.
January 10, 2012 @ 9:13 am
February 7, 2012 @ 2:28 pm
February 17, 2012 @ 7:33 pm
February 21, 2012 @ 8:42 pm
February 19, 2012 @ 3:39 pm
February 21, 2012 @ 8:48 pm
February 24, 2012 @ 4:25 am
The pickups arent working and i get the loudest ‘noise’ when I touch the switch casing. help/suggestions please?
February 28, 2012 @ 9:33 am
March 1, 2012 @ 3:53 am
Good tutorial though!
February 27, 2012 @ 8:02 am
February 28, 2012 @ 9:36 am
February 28, 2012 @ 8:56 am
thanks
February 28, 2012 @ 9:38 am
March 2, 2012 @ 2:44 pm
March 20, 2012 @ 9:58 am
March 14, 2012 @ 5:43 am
March 20, 2012 @ 9:59 am
March 26, 2012 @ 11:46 pm
March 26, 2012 @ 11:47 pm
April 8, 2012 @ 8:54 pm
That guitar has humbuckers, so it’s unlikely to be a EMF/shielding issue. Other process-of-elimination: try different cable, different guitar, different amp, different FX, etc.
April 9, 2012 @ 11:09 am
April 2, 2012 @ 8:13 pm
April 8, 2012 @ 8:56 pm
April 9, 2012 @ 4:13 am
I was wondering if you could please give me your advice on something that I don’t know if is a grounding issue or not. I got an old 60’s amp from the US and to use it in Spain I employ a voltage regulator to 220v. It’s grounded although the amp doesn’t have a 3 prong cord.
April 9, 2012 @ 4:18 am
April 9, 2012 @ 10:26 pm
April 18, 2012 @ 3:44 am
April 18, 2012 @ 8:29 am
April 18, 2012 @ 11:53 am
April 19, 2012 @ 1:26 pm
April 18, 2012 @ 12:00 pm
April 19, 2012 @ 5:10 pm
April 25, 2012 @ 2:30 pm
May 9, 2012 @ 9:18 am
May 21, 2012 @ 6:25 pm
May 24, 2012 @ 5:21 pm
May 30, 2012 @ 7:21 am
June 13, 2012 @ 4:08 pm
June 14, 2012 @ 11:11 am
June 14, 2012 @ 11:04 pm
June 20, 2012 @ 8:15 am
hello there , i have an ibanez rg321mh i have a problem and i hope you guys help me out , when i connect my guitar to the amp directly or with a distortion pedal then everything is cool ut when i touch the steel from out side the pickups and the screw of the pickups switcher and makes big noise and when i touch any metal parts on the guitar nothing happen just when i touch this 2 ones i opend my cavity and every wire is connected and i am sure so how to fix this please !!!
June 24, 2012 @ 9:15 pm
Sounds like you need to ground the pickup body and switch. Try alligator clipping a wire between the pickup cover and the jack ground lug (or cable plug sleeve), and see if that fixes it. If so, solder a wire to the inside of the cover and connect it to the nearest ground point. Similarly for the switch.
-John
June 24, 2012 @ 8:09 am
June 24, 2012 @ 9:41 pm
June 25, 2012 @ 2:31 pm
July 5, 2012 @ 8:55 am
July 6, 2012 @ 5:14 pm
July 6, 2012 @ 7:18 pm
July 6, 2012 @ 7:24 pm
June 25, 2012 @ 5:50 pm
June 28, 2012 @ 7:07 am
Still, you certainly could have a problem with the bridge grounding. Do a test with an alligator lead between your bridge and the jack shield (or have someone hold a wire with one end touching bridge and other touching your metal cord plug). If that changes it, you’ll know!
July 12, 2012 @ 8:49 am
July 12, 2012 @ 11:33 am
July 12, 2012 @ 4:11 pm
July 12, 2012 @ 4:53 pm
July 12, 2012 @ 7:14 pm
July 12, 2012 @ 6:53 pm
July 13, 2012 @ 7:30 am
July 27, 2012 @ 2:54 pm
July 29, 2012 @ 9:10 pm
August 25, 2012 @ 10:51 am
August 12, 2012 @ 11:22 am
August 14, 2012 @ 8:16 am
You can try clipping an alligator lead (or taping a wire) between the bridge and jack shield to see what difference it makes.
August 13, 2012 @ 5:40 am
September 6, 2012 @ 3:48 am
to make the chain from amp & guitar complete.
great tutorial video anyway : )
September 14, 2012 @ 6:14 am
October 6, 2012 @ 1:25 pm
October 7, 2012 @ 10:08 am
October 7, 2012 @ 11:00 am
October 13, 2012 @ 11:58 pm
October 24, 2012 @ 9:07 pm
October 17, 2012 @ 2:19 pm
October 24, 2012 @ 8:55 pm
October 19, 2012 @ 4:53 pm
October 24, 2012 @ 9:03 pm
If you suspect the amp, try playing into a different amp. Or try different amp settings, presets, etc. Try a different cable. And open up the guitar and check on the wiring. A Les Paul is easy to open up and inspect. Good luck!
October 25, 2012 @ 4:39 am
October 30, 2012 @ 3:18 pm
October 31, 2012 @ 12:56 pm
Does your problem occur on a clean amp setting (not high-gain, not very loud)?
November 1, 2012 @ 9:00 pm
November 13, 2012 @ 11:14 am
November 13, 2012 @ 12:25 pm
November 4, 2012 @ 3:54 pm
November 7, 2012 @ 4:18 pm
December 1, 2012 @ 2:43 am
December 4, 2012 @ 1:13 pm
November 7, 2012 @ 12:38 pm
So just a curious question really is why? and maybe if solveable then this will be my temporary solution.
Thanks for your time and your video’s are really ‘complete’ the cover every aspect
November 10, 2012 @ 8:37 am
November 29, 2012 @ 1:23 pm
November 15, 2012 @ 5:32 pm
November 29, 2012 @ 1:21 pm
If your middle pickup is RWRP, is the hum reduced when in switch positions 2 and 4 (combining middle pickup with neck or bridge?)
Have you used a multimeter to check for electrical continuity between all the metal parts of the guitar?
December 1, 2012 @ 2:56 am
December 3, 2012 @ 1:06 pm
December 4, 2012 @ 1:21 pm
December 8, 2012 @ 5:17 pm
The bass costed me a lot, but its kind of dissapointing that my former and cheaper bass actually has more silent electronics.
thanks in advance.
December 8, 2012 @ 5:59 pm
December 9, 2012 @ 7:40 am
December 9, 2012 @ 11:05 am
December 14, 2012 @ 9:10 pm
December 15, 2012 @ 6:58 am
December 15, 2012 @ 7:13 am
December 29, 2012 @ 5:01 pm
December 15, 2012 @ 1:48 pm
December 20, 2012 @ 1:27 pm
December 24, 2012 @ 10:15 pm
December 24, 2012 @ 10:15 pm
December 15, 2012 @ 1:50 pm
December 29, 2012 @ 4:57 pm
December 16, 2012 @ 9:48 am
1. How do I make ground connection to amp chassis with screw? Is there any special screw for that?
2. I read oft about “star grounding” but I don’t really understand how many screw ground connections do I have to make, is it only one?
Thank you and I hope you could help
January 6, 2013 @ 9:47 pm
January 7, 2013 @ 4:56 pm
January 8, 2013 @ 9:16 am
December 29, 2012 @ 12:40 pm
get to the pots ??
if not,,,kindlly explain how you got them all out , and onto that cardboard..
non destructively, sir
thanks
December 29, 2012 @ 4:53 pm
January 1, 2013 @ 11:31 am
January 6, 2013 @ 9:49 pm
January 15, 2013 @ 7:32 am
when i play with clean it makes a tiny bit of distortion sound. i had another amp laying around so i tried changed that. It didnt work. i also tried changing the wire connecting the guitar to the amp. Still, it didnt work. i played around a little bit with the amp settings but still. even if i go ”as clean as possible” i still makes a distortion sound when a note is played. ANY help is greatly appreciated. Thanks.
January 16, 2013 @ 5:30 am
January 16, 2013 @ 8:20 am
January 16, 2013 @ 1:37 pm
January 16, 2013 @ 3:08 pm
January 19, 2013 @ 3:34 pm
January 27, 2013 @ 6:58 am
January 27, 2013 @ 5:31 pm
February 12, 2013 @ 4:48 pm
February 11, 2013 @ 5:22 pm
February 12, 2013 @ 3:23 pm
February 20, 2013 @ 6:40 pm
February 16, 2013 @ 10:14 pm
February 16, 2013 @ 11:46 pm
February 17, 2013 @ 4:55 am
February 24, 2013 @ 1:23 pm
March 7, 2013 @ 10:16 pm
March 8, 2013 @ 1:58 pm
March 10, 2013 @ 1:43 pm
March 13, 2013 @ 10:27 pm
April 6, 2013 @ 10:16 pm
March 14, 2013 @ 8:12 pm
March 16, 2013 @ 3:56 am
My problem is that when I adjust the tone knob of my electric guitar there’s some kind of buzzing sound in my ampli…. and when it’s in 0 the buzzing sound is gone….
is that normal?
March 20, 2013 @ 3:03 pm
March 25, 2013 @ 2:18 am
because sir when i touches the strings the buzzing is gone is it a ground problem?
April 6, 2013 @ 10:02 pm
March 25, 2013 @ 10:37 pm
March 28, 2013 @ 3:02 am
April 6, 2013 @ 10:17 pm
April 7, 2013 @ 11:02 am
April 2, 2013 @ 6:46 am
April 6, 2013 @ 10:01 pm
April 7, 2013 @ 6:19 am
April 7, 2013 @ 9:10 pm
April 8, 2013 @ 3:22 am
April 27, 2013 @ 12:08 pm
May 5, 2013 @ 3:37 pm
May 7, 2013 @ 11:07 am
May 8, 2013 @ 8:27 pm
May 14, 2013 @ 8:32 am
May 24, 2013 @ 3:06 am
May 29, 2013 @ 4:04 pm
June 11, 2013 @ 4:01 am
June 11, 2013 @ 9:08 am
June 11, 2013 @ 4:11 pm
June 20, 2013 @ 2:29 pm
I have a Ibanez fireman, the pickups are huncanceling, but they still make noise when using overdrive. However when i touch the metalpart of my cable which is plugged to guitar, the hum stops. Completly silent. Anyone can diagnose this? The hum doesnt change when touching any other metalparts! Please someone answer!
Thanks
June 24, 2013 @ 9:48 am
July 16, 2013 @ 6:24 am
July 25, 2013 @ 5:29 am
August 16, 2013 @ 1:54 am
September 1, 2013 @ 4:56 pm
September 2, 2013 @ 10:55 am
September 3, 2013 @ 9:28 pm
September 17, 2013 @ 8:27 am
September 17, 2013 @ 8:27 am
September 23, 2013 @ 12:40 pm
September 26, 2013 @ 4:08 pm
September 29, 2013 @ 5:30 pm
I had a lose ground wire and I just re-soldered my output jack’s ground back on and I still have the exact same problem.
October 7, 2013 @ 10:06 am
October 24, 2013 @ 8:38 am
October 26, 2013 @ 12:13 pm
October 29, 2013 @ 3:06 pm
October 29, 2013 @ 3:09 pm
November 1, 2013 @ 9:16 pm
Thanks for the video John, I hope you can answer this question. I have the opposite problem from your video where if I’m touching the strings or bridge, the noise goes away but comes back if I remove my hands.
I have two identically wired strats (one is MIM, one is USA) that I wired myself. The MIM one has this problem, the USA one is dead silent (comparing both with hum canceling on in pickup selector positions 2 and 4). Both have ground wires running to the tremolo claw.
Any suggestions? I have several other guitars and some do this, some don’t. I’d love to track it down.
November 4, 2013 @ 12:28 pm
I wonder if there’s a difference with the shielding?
http://www.guitarnuts.com/wiring/shielding/shield3.php
-John
December 13, 2013 @ 1:02 am
December 28, 2013 @ 3:57 pm
reading?
January 8, 2014 @ 11:48 am
alittle when i touch any metal part. I’m using a fender with humbucker
pickups. I’ve been told it’s normal cause of the pickups. but is there
anyway to get stop the buzz? I know you explained that there is a probably
a problem with the wiring, but i’m fairly new at guitaring and i don’t know
how to fix the wiring..
January 17, 2014 @ 1:05 am
problem was my cable since I stepped on it until it’s head was almost
dislocated. I also tried restarting (on-off-on) my amp and leaving my
effect pedals on. That stopped my buzzing for a decent amount of time.
January 21, 2014 @ 12:07 pm
January 30, 2014 @ 3:40 pm
replace the bridge pickup only to SD JB. Upon coming home and plugging it
in, the bridge pickup and neck were both quiet. However when flipping the
switch to the middle position I’m hearing a lot of buzz/hum, even with my
hand covering the strings.
Is this ground noise that’s causing it? It wasn’t happening before. I
called the guy that did the repair and he tried to explain it’s because
single coil pickups will buzz/hum more than humbuckers. I told him it
wasn’t doing that before!
February 6, 2014 @ 9:04 pm
buzz even i turn my guitar volume to ten and as my amp volume gets higher
the buzz also keeps getting higher what can i do please i need immidiate
help please
February 17, 2014 @ 12:28 pm
the problem is in the circuit.
March 12, 2014 @ 7:17 pm
Any tips?
April 10, 2014 @ 8:42 pm
where a strap would go, and the ground noice is bugging the hell out of Me
when I have it running in the mixer board I got. I was wondering, could you
geive Me some instructions on what wires i’d need to check?
April 29, 2014 @ 12:02 pm
May 9, 2014 @ 3:57 am
make it buzz regardless of internal electronic setup?
June 25, 2014 @ 7:45 am
strings knobs so on the opisate happens, like a click sound, its like i
have static when i dont tutch the metal
June 25, 2014 @ 7:47 am
June 25, 2014 @ 8:11 am
stops
July 1, 2014 @ 12:33 pm
July 4, 2014 @ 1:10 pm
September 1, 2014 @ 6:05 am
bought the guitar and amp from canada ,, am i stuck with that buzz ?
September 8, 2014 @ 6:54 pm
had increased noise in most spots, except where you touched the volume and
tone on top, I believe, where the noise seemed to disappear. Is this just
the video, or did it really disappear? If it did, I am wondering why,
considering all ground was gone. Second, I have a new strat (MIM), and I
get a hum that disappears whenever I touch a metal part. Is this because
of the computers in the room? Or is there something else I should
consider? I’d turn them off to test, but then I’d lose this message. I
will update soon as I do.
September 8, 2014 @ 7:11 pm
gain and volume way up, and had no noise. Not bad for an MIM strat. I
also found that if I grab the body/neck tightly, it does hum. I guess that
is the fact that I am NOT connected to ground myself? It does go away when
I touch the strings. Am I on the spot with this analysis?
October 19, 2014 @ 12:48 pm
What can I do?
October 24, 2014 @ 1:59 am
cheaper made guitars use black hardware that is PAINTED black not blued
using a form of rusting like what some guns use. Blued hardware can carry a
ground better then painted hardware. I have a Dean Vendetta guitar with all
black hardware and even though its grounded threw the bridge it buzzes no
matter what unless you touch the jack when its plugged in. I had to remove
the bridge and lightly sand all the points where the bridge and saddles
touch, i even had to lightly sand the tips of the saddles where the strings
lay over the saddles. NOW finally the guitar is quiet and noise free. It
took alot of work but it was worth it because its a cool guitar for the
money.
November 4, 2014 @ 8:04 pm
strings the noise goes away. I think there is a bad volume pot in there so
maybe that’s the problem? It seems that the volume pot for the bridge
pickup doesn’t turn all the way off and excessive noise until I touch the
strings. Any help is welcomed. Thanks
November 7, 2014 @ 5:43 pm
thought I did a pretty good job wiring it, but when I turn my volume up I
notice a hum, the hum is more obvious when I specifically tap my neck
volume knob (it’s metal). I also noticed that if I bump the 1/4 inch going
into my amp head, it makes a strange sort of being sound. To me it sounds
like my pot has a loose ground and my amp also might need rewired. Any
ideas?
November 14, 2014 @ 10:54 am
correctly, but i’m still getting buzzing. Nothing changes to the sound when
I touch any metal components, and i’ve changed the battery but it still
buzzes. What would you recommend?!
November 28, 2014 @ 8:06 am
problem,its real real bad when on overdrive mode amp…
November 29, 2014 @ 8:28 pm
to fix it coz I really need it. Reply ASAP. Tnx
December 24, 2014 @ 2:07 pm
tutorial of what you did would be more helpfull then just explaining, so no
dude you did not help :\
January 3, 2015 @ 1:02 am
a magic cable or something? can you please tell me what did you clip on
that? please
January 15, 2015 @ 7:26 am
January 15, 2015 @ 4:21 pm
seymour duncan invader bridge pick up and my old fender squire strat and i
completely stripped the stock pick up, 2 tone knobs and 5 way switch and
just left one volume knob and installed the new bridge pick up. i went off
videos and duncans also come with a sheet with instructions wich i
followed. but for some reason i get a slight hum wich stops when i touch
either the metal part of my lead or the metal cover of the jack. if i touch
the bridge it gos a little quieter too. i have also installed a seymour
duncan SH-4 bridge pick up into another guitar i made from parts. the body
already had a cheap humbucker bridge pick up (just the one pick up) and i
took it out and installed the SH-4 but again im getting slight hum even
though i followed the wiring diagram. this guitar also stops buzzing when i
touch the jack area or the lead. its not a loud buzz on either guitars but
its there when it shouldnt be.
January 21, 2015 @ 1:57 pm
string,the buzz stops
February 2, 2015 @ 6:41 am
wiring and adjusting guitar for a couple weeks. and my favorite guitar is
having ground issues. hopefully I can go home and fix it now 🙂 thanks!
February 14, 2015 @ 2:01 pm
March 6, 2015 @ 7:36 pm
ebay; one is just old and the other one had the pickups swapped poorly, it
seems, by someone who forgot the ground. I am worried about getting
electrocuted, so that’s why I found this video… If I solder a wire from
the bridge to the volume pot, will that take care of it? I have 2 guitars
doing this, so I’m hoping this would be the correct solution for both the
tele and strat.
March 11, 2015 @ 4:16 am
it?
March 12, 2015 @ 5:51 pm
to make a crazy discovery I made WRT buzz while not touching the strings or
anything metal on the guitar. My soldering iron was causing this issue!
Yes, when I turned the soldering iron on the buzzing was insane, when I
turned it off it went away. Crazy eh?
March 22, 2015 @ 12:17 am
my guitar was brand new. Any advice on this?
March 31, 2015 @ 2:55 pm
pots, and Sprague .223 capacitor. Still have a ground hum when I let go of
the strings, or any metal parts. Suspecting maybe the input jack. Its a new
guitar too. Everything is wired, everything is grounded {solid solder flow
joints} Scratching my head here…
March 31, 2015 @ 2:55 pm
pots, and Sprague .223 capacitor. Still have a ground hum when I let go of
the strings, or any metal parts. Suspecting maybe the input jack. Its a new
guitar too. Everything is wired, everything is grounded {solid solder flow
joints} Scratching my head here…
April 1, 2015 @ 8:41 pm
while and just was stuck even though I was looking at the wire hanging down
in the Guitar. The sticky stap they use seem to be milting by the heat in
my apartment. No even a lose wire .they groung the wire to the Guittar with
a tape holding the gound to the body for proper grounding. Was stuck to see
it. Thank you .
April 20, 2015 @ 1:32 pm
stops when i touch the metal parts but it only happens when the distortion
is on. when i turn off the distortion i hear no buzzing what so ever.
April 22, 2015 @ 8:10 am
illustrating the issue and explaining the phenomenon. Just confirmed my
guitar’s issue is grounding. Time to get to work and fix the issue!
April 28, 2015 @ 9:51 pm
May 2, 2015 @ 2:34 pm
May 2, 2015 @ 9:35 pm
May 4, 2015 @ 12:54 am
a built in pick up. i plugged my acoustic guitar to my mixer, then my mixer
to the laptop. im getting some strange buzzing noise. i know its not an
alien trying to communicate with me but how can i eliminate the sound?
also, when i pluck the strings im hearing very faint sound in my laptop.
please help 🙂 🙁
May 6, 2015 @ 9:54 am
I know it’s the P90s but do you have any idea how to stop the squealing?
Thanks
June 11, 2015 @ 10:29 pm
this type of hum in the amp to varrying degrees. It almost always occurs at
certain pickup positions and not others. A common one with a five way
switch type guitar, is position 1,3,5 are fine, but there’s hum in
positions 2 and 4. But what really baffles me is brand new guitars even
have this problem. Last year I got a brand spankin new american standard
tele and only the middle pickup position didnt cause hum. WTF?
June 28, 2015 @ 2:34 pm
noise that started after I adjusted the bridge on a Gibson. Looked like the
post had turned and broken off the wire inside. Soldered it back in place
and VIOLA, back to good..
July 3, 2015 @ 10:50 am
July 5, 2015 @ 8:35 am
what appears in the video, only that my guitar won’t play ANY sound at all
and is causing very annoying buzz noices. Do you have any idea of how to
fix this or what it could be? I also don’t want to break anything in the
guitar since it’s quite costly to replace some parts of it. 🙂
July 21, 2015 @ 5:16 pm
bridge pickup the hum I’m getting stops? I know it’s a ground issue but
unsure where to start looking. Thoughts?
July 28, 2015 @ 3:19 am
however my noise doesn’t mutes when i touch my bass parts or turn the
volume down, it shuts itself when i touch the outer part of the jack
plugged in my bass. i checked with all the cables i had and even with a
guitar, same problem, only mutes when i touch the jack. what kind of
problem would that be? thanks